I’m finally on the last part of the posts about my dining chair upcyle project (Part 1, 2 and 3 can be found in the following links – Part 1, Part 2 and Part 3 ) and today I will be sharing the finishing touches that I have added, lessons I have learned and how much the project cost per chair.
Firstly though, the finished chairs…
I finally finished the chairs, it took several weekends to complete but I’ve done it and am really pleased with the outcome! The final finishing touch that I have added is some pompom trim that I used for the alcoves when I decorated the downstairs which I purchased from Amazon (if you missed that post you can find it here) . I decided to add the trim to add a further element of co-ordination into the colour scheme and design of the room and I feel that it pulls all the elements together really well. I like the idea that people will notice all the little touches and will allow their eye to investigate the room in greater detail.
This chairs project was really my first major foray into the world of upcycling and upholstery. I have not worked on a project quite like this before and along the way have learned a few lessons…
- However long you think it will take, double it and add an hour. Sanding the chairs was probably the longest part and I couldn’t believe how much time I spent clearing the old varnish from the frames of the chairs.
- Clearing all the varnish and stripping the frames back to bare wood is the best thing to do for the paint to adhere properly. Failing to clear all the varnish, like on my yellow chair, has resulted in patchy paint and the colour of the varnish bleeding through all the coats of paint I applied. It still looks patchy now and seems to be more noticeable at the bottom of the legs.
- Sometimes it pays to sit back and think a bit…I tried to create a fancy curved corner and edge on the first seat that I tried to upholster which didn’t really work and frustrated me when it didnt go to plan. I should have sat and thought about what I was doing and ways to cover the seat before starting.
- Have fun with your project. Think about what is fun and makes you smile and go with what you think will work. The worst that can happen with a project like this is that you have to sand the chair down and start again.
And here are the costing calculations on the attached document…
Costings for chairs
So, in all the chairs cost £17.63 to upcycle which doesn’t seem too bad when you consider that I have bespoke, one of a kind, unique chairs that fit my home and style perfectly and I have had the experience of learning new skills along the way. And I’m proud to show them off and say “I created these”. I would recommend to anyone that can’t seem to find furniture that they completely like or keep finding thing that are not quite right to go out and see what is available for sale second-hand and try your hand at creating something that you love!
I have shared the first two parts of this project already, you can find the first post (about finding my chairs) here, and the second part (about preparing them and painting) here . Todays post is about upholstering the seat part of the chairs.
I had decided to replace the seat part of the chair fabric with white vinyl and decided that I would replace the seat padding at the same time as the padding was fairly flat and on some chairs felt pretty non existent. I decided to use a thick, 2 inch deep foam for the seat padding which I bought from Amazon. I also needed to buy a staple gun and the vinyl material which I also ordered from Amazon. As the width of the material I chose to use was 1.4 meters I purchased 2 meters in length which gave me enough fabric to cover all 4 seats.
The first task I had was to remove the old fabric from the seats once the seat had been removed from the chair frame. Sounds fairly simple doesn’t it? This task took an age! The old fabric had been stapled to the seat base with about a million staples per seat, and it wasnt just the sheer amount of staples used that made it a lengthy task, the staples were really tough to remove, some of them embedded into the wood quite deeply. I used a screwdriver to lever the staples out one by one. Once the staples had been removed I could see that the seat padding was made up of bits of milled material and foam had been used around the edges of the seat to make them less hard. The foam had disintegrated fairly badly and had in many places turned to dust. I had to carefully remove the fabric and use a Hoover to clean up as I went along.
The foam pads that I had bought were slightly bigger than the seat bases which meant I needed to cut the foam down to size. as the seats were not square I also needed to make sure that the foam shape matched that of the seat so I used the seat as a template and traced around them onto the foam with a sharpie marker before cutting the excess foam away with scissors.
Once the foam had been cut to size I then needed to cut the vinyl down too. I cut the piece I had bought into 4 sections, one piece for each seat. I then laid this down on the table with the facing side to the table and the underside of the fabric facing up. on to this I laid the cut foam and then placed the seat on top. From that point I was able to start securing the fabric to the seat using the staple gun. I started in the centre of the front of the seat, then the back centre, making sure the fabric was taught and evenly stretched over the foam. I then secured each side before trimming down the excess fabric and then continued to staple the fabric into place. Once I reached the corners I chose to fold the fabric and tuck it in, creating a neat looking corner. I had, on the first chair. attempted to be fancy and create rounded seat edged but it didn’t work particularly well and I ended up with excess fabric in one corner and an awkward looking seat covering. In hindsight I think that if the foam hadn’t been so thick then that idea would have worked a lot better!
In the pictures above you will be able to see that I started with stapling the corners of the fabric first…this was the first seat that I covered where I thought that making the corners rounded was a good idea…it wasn’t! And starting on the corners meant that the tension of the fabric was out which made it harder to get the fabric to lay nicely over the foam. On the other seats I secured the fabric in the centre of the sides and worked front centre 0 back centre, then both sides in the centre before working my way along the rest of the sides and out towards the corners. Unfortunately, I forgot to take any more pictures of the full method I used….
Next week I will be showing you the completed chairs and the fun decoration I have added to the chairs!
A little while ago I sort of, nearly finished a upcycle project I have been working on. And when I say “sort of nearly” I just mean that the majority of the hard work has been done and to any other person the project would look to be complete, but, I have more teeny things I would like to do in order for me to feel that the project has come to a close. The project I am referring to is my dining chairs.
When I moved in to my home I had a dining table but no chairs, which in turn meant nowhere for guests to sit should I decide to invite anyone over for food unless sitting on the sofa and balancing a plate on your knees is acceptable in any circumstances other than when you are alone. I started searching on Facebook, (who happen to have introduced a nifty little feature called “Marketplace” which seems to round-up any selling adverts from groups and put them all in one place which you can search on by either selecting certain categories or adding your own search terms), for dining chairs or chairs of any kind that I could use as substitutes. I found some pretty decent looking plastic school chairs that I thought would be ok, they were orange which I loved and free too! I messaged the seller but he didn’t want to let me have 4 of them, he had 36 to get rid of and wanted them gone en-mass. I contacted a few other people who had chairs up for free but either they had already been collected by someone else or else I had no reply. I sort of gave up looking and had decided that eventually I would probably have to buy some which is when I found “the ones”….
I can’t remember what I was looking for on Marketplace, all I know is that I wasn’t looking for chairs, but an ad caught my eye purely because the chairs in question reminded me of the ones my Mum and Dad had when I was growing up…they had the same shape to them, the same fabric, the same colour varnish, the only thing that was different was the back rest of the chairs, the ones in the ad had low backs where the ones Mum and Dad owned had high backs. Out of interest I clicked on the ad and found that the owner was giving them away for free! I sent a message and collected them later that day.
I’ve got a white table and the rest of the furniture in my dining area is white so having brown and orange chairs wasn’t really going to match very well. I decided that I would re-paint the chairs. My initial idea was to paint the chairs white with a possibility of renewing the fabric on the seats, I was going to pick out similar colours to boxes I have in my storage unit that are pink, blue, yellow and white. I changed my mind about having white chairs with coloured seats as I found it hard to find fabric in colours I was happy with or that weren’t mega bucks and out of my price range. After a bit of extra thought and research into costs I decided that I would paint the chairs different colours and chose a white vinyl fabric to do all the seats with.
Next week I will be sharing the first part of the project with you!